Outlive the Outbreak Banner-01

DIY Fish Trap

By on October 26, 2013

1743313_10201925946363310_1522188705_n

Here is an easy DIY method for creating a fish trap

Step 1: Materials and such

step1 ste1 st1

Most of the materials and such in this project can be substituted and worked around depending on what you have.

materials
-wire mesh,
-plastic mesh
-some sort of mesh
It needs to be small enough that the fishes cannot swim out of it. I used a plastic mesh that i got from the fencing department in lowes
-thin enamel coated wire
-thick wire
-2 dowels,
They don’t need to be very thick, i used bamboo kebabs.
poster board, wrapping paper
something that you can use to make a cone stencil


Tools
wire cutters
something to cut the mesh with
needle nose pliers 

Step 2: Cut the piece

step2

The trap consist of four pieces , two cones , the cylinder body and the door.

to make the cylinder body just measure out a rectangle of the mesh, The cylinder should be about twice as long as it is wide so keep that in mind when you cut the rectangle.. This step isn’t real hard its basically cut a rectangle.

Step 3: Roll and connect

step3 ste3

So now you need to roll the rectangle into a cylinder . Try to leave and overlap of about 2 units of the mesh. Then used the thin wire to weave the two sides together Start at the edge of the mesh and work across making a seam. Do it as if you were sewing the mesh together with the wire and every so often make a couple loops around the two edges to reinforce it. Using need nose pliers to pull it through it makes it much easier.

Step 4: Ah yes the cones, the cones

step4 ste4 st4

The cones are made out of a half circle of the mesh rolled into cone shape and connected with the wire. I found that the best way to make it fit was to first make a cut out with the poster board and then adjust it to make it perfect then use that piece as a guide line for the mesh. Its best to keep a little extra on the cone piece because its much easier to trim down than it is to stretch it. The angle of the cone should not be to steep Mine was about the same as a typical kitchen funnel. middle of the cone should be a little bigger than the size of fish you want to catch. don’t try to catch avery big fish without a very big trap because it will not work.

Step 5: And now for the hard part

step5 ste5 ste5

The attaching of the cones to the cylinder is the hard part. The cones need to be inverted and attached with the wire to the outside edge of the cylinder. This is also the part where you need to trim off any extra on the cones to make them fit well. start at one point on the edge of the cone and cylinder and then “sew” around the cylinder.

Step 6: And now for the harder part

step6 ste6 ste6 st6 s6 6

This part requires an arc welder, plasma cutter and a large jackhammer. Or you can use wire cutters and scissors. now that you have you lovely cylinder and two inverted cones on either side its time to add the door. The door is most critical to removing the fish you caught and adding bait and weight. Decide what size you want your door to be and then cut out a piece of the cylinder that size. Next find a piece that when folded in half is about an inch bigger than the opening on all sides. Fold the piece in half to double it over and make it stronger.
To stiffen the door I used a piece of thick wire that a wound through the piece of mesh on the side of the mesh that was not closed from folding over.

Step 7: Attaching said door

step7 ste7

Uses a coil of thick wire to attach the door. twist the coil of wire through the mesh on the top of the door and the top of the opening. If you look at a composition notebook that has the wire coil then you can see and example. Then uses two little loops of wire to secure the two sides of the door hinge.

by austin

1743313_10201925946363310_1522188705_n

About The Survivalist

Total bacon buff. Explorer. Survivalist Expert. Zombie Fanatic/Hunter. Internet Entrepreneur

One Comment

  1. Pingback: DIY Fish Trap | SHTF R U Ready?

Leave a Reply

Your email address will not be published. Required fields are marked *